Permit and Inspection
We pull the Frankfort permit and schedule the inspection. You don't fill out paperwork or chase the city. The permit and inspection are part of the install price, not a surprise line item later.
Every tankless install we do covers the full job, not just the box on the wall. You get the permit, the gas or electrical work, the venting, the startup, and the walkthrough. Here's what's in the standard scope, and what we quote separately if your home needs it.
We pull the Frankfort permit and schedule the inspection. You don't fill out paperwork or chase the city. The permit and inspection are part of the install price, not a surprise line item later.
For gas units we run and pressure-test the dedicated gas line, usually 3/4-inch copper or PEX. For electric units we run the 240-volt circuit and confirm the panel has capacity. Both are included in the quoted price.
We install the manufacturer's stainless vent kit through the wall or roof, with correct slope and clearances to code. Condensate routing is included on condensing units so acidic water doesn't rot your wall or floor.
We drain, disconnect, and haul away your old tank heater. No extra charge for disposal, and no tank sitting at the curb for weeks. We also clean the mechanical space before the new unit goes up.
We purge air from the lines, set the output to 120 degrees F, and test hot water at every fixture. You get a walkthrough of the controls and the annual flush procedure before we leave.
We register the manufacturer warranty on your behalf and hand you the paperwork. Our workmanship warranty is included, and we note the install date so you know when the annual service is due.
Tankless water heater installation Frankfort KY is the process of removing a storage-tank water heater and mounting a wall-hung unit that heats water on demand as it flows through a heat exchanger. The job involves running a dedicated gas line or 240-volt circuit, installing stainless steel venting, mounting the unit to code, and flushing the lines before startup. Most homes need 6 to 10 feet of new gas pipe, a pressure relief valve, and a shutoff within reach of the unit.
Frankfort homes built before 1980 often have 1/2-inch gas lines that can't feed a 199,000 BTU tankless unit, so we upsize to 3/4-inch copper or PEX tubing before the install. If you're comparing tankless water heater cost Frankfort, Kentucky against a tank replacement, the upfront number is higher, but the unit lasts 20 years versus 10 and cuts gas use by 20 to 30 percent. We handle gas tankless water heater installation Plumbers Frankfort KY wide, from Downtown to Peaks Mill.
We run a five-step install from first call to final test. Most jobs finish in one day, and you get a written price before we cut a single pipe. Here's exactly what happens when you book tankless water heater services Frankfort KY.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Pipe wrench and tube cutter
Used to break down old galvanized or copper connections and cut new pipe to length. Clean cuts mean fewer leaks at the fitting.
PEX crimping tool
Crimps PEX tubing connections for water lines. Faster and more reliable than solder in tight mechanical closets.
Soldering torch
Used for copper pipe joints on gas and water lines where code or routing calls for copper. We pressure-test every soldered joint.
Pressure gauge
Tests the gas line and water system for leaks before startup. A 15-minute pressure hold tells us the connections are sound.
Leak detection equipment
Finds hidden water leaks around the unit and supply lines after install, so a slow drip doesn't rot the wall behind the unit.
Pipe camera inspection system
Scopes vent runs and supply lines when routing is unclear, especially in older Frankfort homes with remodeled walls.
Uniform Plumbing Code and Kentucky Plumbing Code compliance
We follow UPC and Kentucky Plumbing Code on gas sizing, venting, pressure relief, and clearances. The permit and inspection confirm the work meets code, which protects your insurance and resale.
Manufacturer sizing and venting charts
Rheem, Rinnai, and Navien each publish sizing and venting tables. We follow them exactly rather than guessing, so the unit performs to spec and the warranty stays intact.
Gas line pressure test
We isolate the new gas line, pressurize it, and hold it with a gauge before opening the valve. Any drop means a leak we fix before the unit fires.
Annual descaling flush
We install a service valve kit and show you how to flush the heat exchanger with a pump and descaler once a year. It's the single best thing you can do for unit life in Frankfort's water.
01
What we do: We install a 199,000 BTU gas tankless unit with a 3/4-inch gas line and stainless venting. The unit heats water on demand, so the tank size limit disappears.
→ Back-to-back showers, laundry, and dishwasher all run at once without a temperature drop. The gas bill drops 20 to 30 percent versus the old tank.
02
What we do: We mount a compact electric tankless unit high on the wall and reroute the 240-volt circuit. The floor space comes back for storage or a stackable washer.
→ Two square feet of wall replaces a 2-foot-by-2-foot tank footprint, and the closet becomes usable again.
03
What we do: We run a new gas line from the meter, install a condensing tankless unit with PVC venting, and handle the permit and inspection.
→ The home moves from a 40-gallon electric tank to endless gas hot water, with lower operating cost and a 20-year service life.
04
What we do: We schedule the swap before failure, size the unit, pull the permit, and install in one day with no emergency premium.
→ The old tank is hauled off before it leaks, and the new unit is under warranty from day one.
Frankfort's housing stock shapes every tankless install. Downtown and South Frankfort homes often date to the early 1900s, with 1/2-inch gas lines, knob-and-tube remnants, and mechanical closets sized for a 40-gallon tank. We upsize gas lines to 3/4-inch and find vent routes that clear the roof or side wall without cutting through historic trim. Winter incoming water temperature drops to about 45 degrees F, which cuts tankless output by 20 to 30 percent, so we size up rather than install a unit that struggles in January. Kentucky Plumbing Code and Uniform Plumbing Code govern venting and pressure relief, and we pull the permit every time. If you're comparing tankless water heater rebates Frankfort, Kentucky against the install cost, we'll tell you which federal or utility incentives apply to your unit. From Buffalo Trace to Versailles Road, we've seen the same issues and know how to solve them.
Downtown Frankfort
Older homes with tight mechanical closets and 1/2-inch gas lines. We plan vent routing carefully to avoid historic trim and upsize gas service where needed.
Frankfort Heights
Mid-century ranches with gas furnaces and 3/4-inch service. Many homes here can take a 199,000 BTU unit with a short gas line run.
Bellepoint
Mixed housing stock, including 1940s bungalows. Wall space for a tankless unit is often tight, so we mount high and reroute venting through the side wall.
Peaks Mill
Rural properties on well water. We check water hardness and sediment before sizing, and recommend a descaling schedule based on test results.
Cold winter incoming water near 45 degrees F
Tankless output drops as incoming water gets colder. We size up 20 to 30 percent so the unit keeps up in January, not just in July.
Older 1/2-inch gas service lines
Most pre-1980 Frankfort homes need a gas line upsize to 3/4-inch to feed a 199,000 BTU unit. We check meter capacity during sizing and include the upsize in the quote.
Moderately hard water at 7 to 10 grains per gallon
Scale builds in the heat exchanger without annual flushing. We install service valves and set a yearly descaling reminder to protect efficiency and warranty.
Most tankless headaches trace back to a rushed install or a unit sized for the wrong house. We fix the underlying cause, not just the symptom, so you're not calling us back in six months.
Problem
A 40-gallon tank can't keep up with two showers and a laundry at once. Families schedule around the tank and still get a cold surprise.
Our Fix
We size a tankless unit to your fixture count and incoming water temperature, usually 199,000 BTU for a two-bath home. Output of 7 to 11 gallons per minute means the third shower stays hot.
Problem
A leaking tank can dump 40 gallons on the floor before you notice. Water heater leaks damage flooring, drywall, and stored belongings fast.
Our Fix
We shut off the water, drain and haul off the old tank, and install a wall-hung tankless unit in the same day. No tank means no tank leak to worry about again.
Problem
A tankless unit on a 1/2-inch gas line starves for fuel, throws error codes, and shuts down mid-shower. It's the most common bad-install problem we see.
Our Fix
We check meter capacity and gas line size during sizing, then upsize to 3/4-inch copper or PEX tubing and pressure-test with a gauge before startup. The unit gets the fuel it needs.
Problem
Frankfort water runs 7 to 10 grains per gallon. Scale builds inside the heat exchanger, cuts efficiency, and can void the warranty if the unit isn't flushed.
Our Fix
We install a descaling port and walk you through the annual flush with a pump and vinegar or descaler. One flush a year protects the heat exchanger and keeps the warranty valid.
A tankless unit changes how your house uses hot water. No standby tank means no running out mid-shower, no 40-gallon tank heating all day, and no wet-floor surprise when the tank rusts through. Here's what Frankfort homeowners notice first.
Endless Hot Water
A tankless unit heats water as you use it, so the third shower in a row stays hot. Families in Frankfort Heights with two full baths and a laundry running at once stop scheduling showers around a 50-gallon tank. Output runs 7 to 11 gallons per minute depending on the model and incoming water temperature.
Lower Gas Bills
Tankless units only fire when a faucet opens. The U.S. Department of Energy puts tankless efficiency at 22 to 34 percent lower energy use than a storage tank in a typical home. Frankfort homeowners with gas heat often see $15 to $30 a month drop on their winter bill after switching.
20-Year Service Life
A well-maintained tankless unit lasts 20 years or more; a tank heater averages 10 to 12. That's two tank replacements you skip. We flush the heat exchanger with a descaling pump once a year to protect that lifespan, especially with Frankfort's moderately hard water at 7 to 10 grains per gallon.
Frees Up Floor Space
A wall-hung unit takes about 2 square feet of wall and sits at eye level. In South Frankfort bungalows and Bellepoint homes where the water heater eats a closet, that reclaimed space becomes storage or a stackable washer setup. We mount the unit high enough to keep the vent terminal clear of snow line.
Typical 2026 pricing in Frankfort runs $2,800 to $5,500 installed for a gas tankless unit and $1,800 to $3,800 for electric. The range reflects gas line size, vent routing, and whether the electrical panel needs an upgrade. We quote a firm price after the on-site sizing visit, so you're not guessing. If you're weighing tankless water heater cost Frankfort, Kentucky against a tank replacement, we'll show both numbers side by side and let you decide.
Typical Investment Range
$1,800 - $5,500 depending on fuel type and scope
A tankless unit lasts 20 years and cuts gas use 22 to 34 percent. Spread over its life, the installed cost is often lower than two tank replacements plus a decade of standby heat loss.
What changes the price
Gas line size and run
A 1/2-inch line that needs upsizing to 3/4-inch adds $400 to $900 depending on length and routing. A short run from an existing 3/4-inch line keeps the price at the low end.
Vent routing
Side-wall venting is simpler and cheaper than roof venting. Roof penetrations, long vent runs, and condensing unit PVC routing add $300 to $800 to the job.
Electrical panel capacity
Electric tankless units draw 60 to 120 amps. If your panel is full or the service is undersized, a panel upgrade adds $1,200 to $2,500 before the unit goes in.
Unit model and BTU
A 150,000 BTU unit for a small home costs less than a 199,000 BTU condensing unit. Rheem, Rinnai, and Navien models vary by $300 to $700 depending on efficiency and features.
Permit and inspection
The Frankfort permit and inspection are included in our quote. Skipping the permit saves nothing in the long run and can void insurance or stall a sale.
Google ★★★★★4.9
Fast, clean tankless install in South Frankfort. They upsized the gas line, pulled the permit, and passed inspection first try. Endless hot water and a lower gas bill.
Google ★★★★★4.8
Quoted a firm price after measuring the gas line and meter. Installed a Navien unit in one day. The techs explained the annual flush and left the mechanical closet cleaner than they found it.
BBB ★★★★★4.9
Converted our 1940s Bellepoint house to gas tankless. They found a vent route that worked without cutting historic trim. On time, licensed, and the work passed inspection.
Our technicians hold Kentucky Master Plumber and Journeyman Plumber licenses and carry Backflow Prevention Certification. We work to the Kentucky Plumbing Code and the Uniform Plumbing Code on every install, and we pull permits rather than skip them. Tankless work is unforgiving: undersized gas lines cause flame failures, wrong venting causes code violations, and bad condensate routing rots a wall. We've installed and serviced gas and electric tankless units across Franklin County, from 100-year-old Downtown Frankfort houses to new builds off Versailles Road, and we size each unit to the home rather than selling a one-size box.
Real experiences from customers who chose our Tankless Water Heater Installation services.
“Our 15-year-old tank started leaking on a Friday. The crew came out Saturday morning, quoted a Rinnai unit, and installed it Monday. They upsized the gas line and ran new venting through the side wall. Endless hot water now, and the gas bill dropped about $22 the first month. Clean work, no mess left behind.”
Dana R.
Homeowner, South Frankfort
“I got three quotes for tankless water heater installation and these guys were the only ones who actually measured the gas line and checked the meter. They explained why a 199,000 BTU Navien needed 3/4-inch pipe. Install took one day, inspection passed first try, and they walked me through the annual flush.”
Marcus T.
Homeowner, Frankfort Heights
“We converted to a gas tankless unit in a 1940s house with a tiny mechanical closet. They mounted it high on the wall, rerouted the vent, and freed up the floor space for a stackable washer. The techs were on time, polite, and answered every question. Hot water never runs out now, even with two teenagers.”
Ellen K.
Homeowner, Bellepoint
Real answers to the questions we hear most often from local homeowners and property managers.
A tank that lets go at 2 a.m. is an emergency. We shut off the water, stop the damage, and can often roll a tankless install into the repair visit so you're not paying twice for the same trip.
View Emergency PlumbingTankless units don't fix slow drains, but we clear them while we're on site. If your install day reveals a clogged drain or a running toilet, we handle it in the same visit with a drain snake or hydro jetting machine.
View Drain CleaningNot sure whether to repair or replace? We diagnose tank and tankless units, including error codes and failed heat exchangers, and give you an honest repair-versus-replace number before you commit to a new install.
View Water Heater RepairIf tankless isn't the right fit for your home, we install and replace traditional tank heaters in Bradford White and A.O. Smith models. Same permit, same code-correct work, sized to your household.
View Water Heater InstallationA water heater leak can masquerade as a slab leak or a failing fitting. We use leak detection equipment and a pipe camera inspection system to find the source before we install anything new.
View Leak DetectionFrozen pipes and burst pipe repairs are common after a Frankfort cold snap. We fix the line, then check that your new tankless unit's supply and condensate lines are protected against the next freeze.
View Burst Pipe RepairCall us any time, day or night. For non-emergency work, we schedule same-day and next-day appointments across Frankfort. Tell us what's going on and we'll give you a time window and a price range before we head out. You can also email us, but for anything urgent, pick up the phone.
Phone
(831) 293-1204Address
1098 S Broadway #120, Lexington, KY 40504
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available